WAVLINK Router Default Login, IP & Password Guide
Administrative web portal for WAVLINK Quantum, Halo, and high-power outdoor Wi-Fi routers.
Use these verified administrative credentials and network addresses to access your WAVLINK router's local setup dashboard.
wifi.wavlink.com192.168.10.1192.168.10.1192.168.1.1adminadminWAVLINK-XXXX / WAVLINK-NDefault password is 'admin'. Wizard prompts for custom password upon completing initial internet setup.
Follow this 4-step walkthrough to access your WAVLINK management settings in less than 2 minutes.
Step 1: Connect to Network
Connect to WAVLINK Wi-Fi network.
Step 2: Open Web GUI or Gateway IP
Open web browser and visit http://wifi.wavlink.com or http://192.168.10.1.
Step 3: Enter Admin Credentials
Log in with default password 'admin'.
Step 4: Configure Settings & Save
Configure router mode, access point mode, or WISP repeater.
These default credentials and IP addresses apply to the following popular WAVLINK wireless routers, mesh nodes, and modem gateways:
If the default password doesn't work or you forgot your custom administrator password, resetting the router restores all factory default settings.
- Make sure your WAVLINK router is connected to power and the power LED is solid ON.
- Locate the physical Reset pinhole button on the back or bottom panel of the unit.
- Use a straightened paperclip, SIM ejector tool, or pin to press and hold down the Reset button for 10 to 15 seconds.
- Release the button once the front panel LED indicator lights begin flashing or turn amber.
- Wait 2 to 3 minutes for the router to complete its reboot cycle.
- Reconnect to the factory default Wi-Fi network (
WAVLINK-XXXX / WAVLINK-N) and log in using usernameadminand passwordadmin.
Cannot reach wifi.wavlink.com or 192.168.10.1 in browser
Ensure your device is connected directly to your WAVLINK router's Wi-Fi network or plugged into a numbered LAN port with an Ethernet cable. If you are connected to cellular data or an active VPN, disconnect them as they route DNS requests away from the local router gateway.
Default login password "admin" is not accepted
Check the physical sticker on the bottom or back of your WAVLINK router. Many modern models print a unique factory admin password or Wi-Fi key. If the password was changed during initial setup and forgotten, press the Reset pinhole button for 10 seconds to restore factory credentials.
Browser displays "Connection Not Private" or SSL Certificate Warning
Most local router administration consoles use self-signed SSL certificates when accessed via HTTPS (https://192.168.10.1). Click "Advanced" and select "Proceed to 192.168.10.1 (unsafe)" to continue securely to the local management dashboard.
How to discover your WAVLINK router's exact gateway IP address
On Windows, press Win+R, type "cmd", hit Enter, and run "ipconfig". Look for the "Default Gateway" IPv4 address. On Mac, open System Settings > Network > Wi-Fi > Details > TCP/IP to find the "Router" IP.
What is the default IP address and login for WAVLINK routers?
The primary default gateway IP address for WAVLINK routers is 192.168.10.1 (with fallback subnets 192.168.1.1). The default web administrative address is wifi.wavlink.com. Out of the box, the default username is admin and the default password is admin.
How do I log in to my WAVLINK router settings?
1) Connect your computer or phone to your WAVLINK Wi-Fi or plug into a LAN Ethernet port.
2) Open a browser and type http://wifi.wavlink.com or http://192.168.10.1.
3) Enter username admin and password admin.
4) Access the dashboard to configure Wi-Fi password, SSID name, port forwarding, and security settings.
How do I factory reset my WAVLINK router?
With the WAVLINK router powered ON, locate the small Reset pinhole on the rear or bottom panel. Insert an unfolded paperclip or pin and hold the button down for 10 to 15 seconds until the power and Wi-Fi LEDs start flashing. Release the button and wait 2-3 minutes for the router to reboot into factory default state.
Does WAVLINK have an official mobile app for setup and controls?
Yes, WAVLINK offers the WAVLINK Mesh App available for iOS and Android smartphones. You can use it to set up new networks, monitor connected devices, run speed tests, and pause internet access.
How do I change the Wi-Fi name (SSID) and password on my WAVLINK router?
Log in to the WAVLINK admin page (http://192.168.10.1), navigate to Wireless, Wi-Fi Settings, or Basic > Wireless. Update the 2.4 GHz and 5 GHz Network Name (SSID) and set a secure WPA2/WPA3 password. Click Apply or Save to restart the wireless radios with your new settings.
Explore default login guides and IP addresses for alternative router brands: